diff --git a/arch/mips/mach-mt7620/Kconfig b/arch/mips/mach-mt7620/Kconfig
new file mode 100644
index 0000000..396fbd0
--- /dev/null
+++ b/arch/mips/mach-mt7620/Kconfig
@@ -0,0 +1,113 @@
+menu "MediaTek MIPS platforms"
+	depends on ARCH_MT7620
+
+config SYS_MALLOC_F_LEN
+	default 0x1000
+
+config SYS_SOC
+	default "mt7620" if SOC_MT7620
+
+choice
+	prompt "MediaTek MIPS SoC select"
+
+config SOC_MT7620
+	bool "MT7620/8"
+	select MIPS_L1_CACHE_SHIFT_5
+	help
+	  This supports MediaTek MIPS MT7620 family.
+
+endchoice
+
+choice
+	prompt "Board select"
+
+endchoice
+
+choice
+	prompt "Boot mode"
+
+config BOOT_RAM
+	bool "RAM boot"
+	depends on SUPPORTS_BOOT_RAM
+	help
+	  This builds an image that is linked to a RAM address. It can be used
+	  for booting from CFE via TFTP using an ELF image, but it can also be
+	  booted from RAM by other bootloaders using a BIN image.
+
+config BOOT_ROM
+	bool "ROM boot"
+	depends on SUPPORTS_BOOT_RAM
+	help
+	  This builds an image that is linked to a ROM address. It can be
+	  used as main bootloader image which is programmed onto the onboard
+	  flash storage (SPI NOR).
+
+endchoice
+
+choice
+	prompt "DDR2 size"
+
+config ONBOARD_DDR2_SIZE_256MBIT
+	bool "256MBit (32MByte) total size"
+	depends on BOOT_ROM
+	help
+	  Use 256MBit (32MByte) of DDR total size
+
+config ONBOARD_DDR2_SIZE_512MBIT
+	bool "512MBit (64MByte) total size"
+	depends on BOOT_ROM
+	help
+	  Use 512MBit (64MByte) of DDR total size
+
+config ONBOARD_DDR2_SIZE_1024MBIT
+	bool "1024MBit (128MByte) total size"
+	depends on BOOT_ROM
+	help
+	  Use 1024MBit (128MByte) of DDR total size
+
+config ONBOARD_DDR2_SIZE_2048MBIT
+	bool "2048MBit (256MByte) total size"
+	depends on BOOT_ROM
+	help
+	  Use 2048MBit (256MByte) of DDR total size
+
+endchoice
+
+choice
+	prompt "DDR2 chip width"
+
+config ONBOARD_DDR2_CHIP_WIDTH_8BIT
+	bool "8bit DDR chip width"
+	depends on BOOT_ROM
+	help
+	  Use DDR chips with 8bit width
+
+config ONBOARD_DDR2_CHIP_WIDTH_16BIT
+	bool "16bit DDR chip width"
+	depends on BOOT_ROM
+	help
+	  Use DDR chips with 16bit width
+
+endchoice
+
+choice
+	prompt "DDR2 bus width"
+
+config ONBOARD_DDR2_BUS_WIDTH_16BIT
+	bool "16bit DDR bus width"
+	depends on BOOT_ROM
+	help
+	  Use 16bit DDR bus width
+
+config ONBOARD_DDR2_BUS_WIDTH_32BIT
+	bool "32bit DDR bus width"
+	depends on BOOT_ROM
+	help
+	  Use 32bit DDR bus width
+
+endchoice
+
+config SUPPORTS_BOOT_RAM
+	bool
+
+endmenu
diff --git a/arch/mips/mach-mt7620/Makefile b/arch/mips/mach-mt7620/Makefile
new file mode 100644
index 0000000..1f3e65e
--- /dev/null
+++ b/arch/mips/mach-mt7620/Makefile
@@ -0,0 +1,8 @@
+# SPDX-License-Identifier: GPL-2.0+
+
+obj-y += cpu.o
+
+ifndef CONFIG_SKIP_LOWLEVEL_INIT
+obj-y += ddr_calibrate.o
+obj-y += lowlevel_init.o
+endif
diff --git a/arch/mips/mach-mt7620/cpu.c b/arch/mips/mach-mt7620/cpu.c
new file mode 100644
index 0000000..457f09f
--- /dev/null
+++ b/arch/mips/mach-mt7620/cpu.c
@@ -0,0 +1,69 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018 Stefan Roese <sr@denx.de>
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <ram.h>
+#include <asm/io.h>
+#include <linux/io.h>
+#include <linux/sizes.h>
+#include "mt76xx.h"
+
+#define STR_LEN			6
+
+#ifdef CONFIG_BOOT_ROM
+int mach_cpu_init(void)
+{
+	ddr_calibrate();
+
+	return 0;
+}
+#endif
+
+int dram_init(void)
+{
+	gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE, SZ_256M);
+
+	return 0;
+}
+
+int print_cpuinfo(void)
+{
+	static const char * const boot_str[] = { "PLL (3-Byte SPI Addr)",
+						 "PLL (4-Byte SPI Addr)",
+						 "XTAL (3-Byte SPI Addr)",
+						 "XTAL (4-Byte SPI Addr)" };
+	const void *blob = gd->fdt_blob;
+	void __iomem *sysc_base;
+	char buf[STR_LEN + 1];
+	fdt_addr_t base;
+	fdt_size_t size;
+	char *str;
+	int node;
+	u32 val;
+
+	/* Get system controller base address */
+	node = fdt_node_offset_by_compatible(blob, -1, "ralink,mt7620a-sysc");
+	if (node < 0)
+		return -FDT_ERR_NOTFOUND;
+
+	base = fdtdec_get_addr_size_auto_noparent(blob, node, "reg",
+						  0, &size, true);
+	if (base == FDT_ADDR_T_NONE)
+		return -EINVAL;
+
+	sysc_base = ioremap_nocache(base, size);
+
+	str = (char *)sysc_base + MT76XX_CHIPID_OFFS;
+	snprintf(buf, STR_LEN + 1, "%s", str);
+	val = readl(sysc_base + MT76XX_CHIP_REV_ID_OFFS);
+	printf("CPU:   %-*s Rev %ld.%ld - ", STR_LEN, buf,
+	       (val & GENMASK(11, 8)) >> 8, val & GENMASK(3, 0));
+
+	val = (readl(sysc_base + MT76XX_SYSCFG0_OFFS) & GENMASK(3, 1)) >> 1;
+	printf("Boot from %s\n", boot_str[val]);
+
+	return 0;
+}
diff --git a/arch/mips/mach-mt7620/ddr_calibrate.c b/arch/mips/mach-mt7620/ddr_calibrate.c
new file mode 100644
index 0000000..75763c4
--- /dev/null
+++ b/arch/mips/mach-mt7620/ddr_calibrate.c
@@ -0,0 +1,308 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018 Stefan Roese <sr@denx.de>
+ *
+ * This code is mostly based on the code extracted from this MediaTek
+ * github repository:
+ *
+ * https://github.com/MediaTek-Labs/linkit-smart-uboot.git
+ *
+ * I was not able to find a specific license or other developers
+ * copyrights here, so I can't add them here.
+ *
+ * Most functions in this file are copied from the MediaTek U-Boot
+ * repository. Without any documentation, it was impossible to really
+ * implement this differently. So its mostly a cleaned-up version of
+ * the original code, with only support for the MT7628 / MT7688 SoC.
+ */
+
+#include <common.h>
+#include <linux/io.h>
+#include <asm/cacheops.h>
+#include <asm/io.h>
+#include "mt76xx.h"
+
+#define NUM_OF_CACHELINE	128
+#define MIN_START		6
+#define MIN_FINE_START		0xf
+#define MAX_START		7
+#define MAX_FINE_START		0x0
+
+#define CPU_FRAC_DIV		1
+
+#if defined(CONFIG_ONBOARD_DDR2_SIZE_256MBIT)
+#define DRAM_BUTTOM 0x02000000
+#endif
+#if defined(CONFIG_ONBOARD_DDR2_SIZE_512MBIT)
+#define DRAM_BUTTOM 0x04000000
+#endif
+#if defined(CONFIG_ONBOARD_DDR2_SIZE_1024MBIT)
+#define DRAM_BUTTOM 0x08000000
+#endif
+#if defined(CONFIG_ONBOARD_DDR2_SIZE_2048MBIT)
+#define DRAM_BUTTOM 0x10000000
+#endif
+
+static inline void cal_memcpy(void *src, void *dst, u32 size)
+{
+	u8 *psrc = (u8 *)src;
+	u8 *pdst = (u8 *)dst;
+	int i;
+
+	for (i = 0; i < size; i++, psrc++, pdst++)
+		*pdst = *psrc;
+}
+
+static inline void cal_memset(void *src, u8 pat, u32 size)
+{
+	u8 *psrc = (u8 *)src;
+	int i;
+
+	for (i = 0; i < size; i++, psrc++)
+		*psrc = pat;
+}
+
+#define pref_op(hint, addr)						\
+	__asm__ __volatile__(						\
+		".set	push\n"						\
+		".set	noreorder\n"					\
+		"pref	%0, %1\n"					\
+		".set	pop\n"						\
+		:							\
+		: "i" (hint), "R" (*(u8 *)(addr)))
+
+static inline void cal_patgen(u32 start_addr, u32 size, u32 bias)
+{
+	u32 *addr = (u32 *)start_addr;
+	int i;
+
+	for (i = 0; i < size; i++)
+		addr[i] = start_addr + i + bias;
+}
+
+static inline int test_loop(int k, int dqs, u32 test_dqs, u32 *coarse_dqs,
+			    u32 offs, u32 pat, u32 val)
+{
+	u32 nc_addr;
+	u32 *c_addr;
+	int i;
+
+	for (nc_addr = 0xa0000000;
+	     nc_addr < (0xa0000000 + DRAM_BUTTOM - NUM_OF_CACHELINE * 32);
+	     nc_addr += (DRAM_BUTTOM >> 6) + offs) {
+		writel(0x00007474, (void *)MT76XX_MEMCTRL_BASE + 0x64);
+		wmb();		/* Make sure store if finished */
+
+		c_addr = (u32 *)(nc_addr & 0xdfffffff);
+		cal_memset(((u8 *)c_addr), 0x1F, NUM_OF_CACHELINE * 32);
+		cal_patgen(nc_addr, NUM_OF_CACHELINE * 8, pat);
+
+		if (dqs > 0)
+			writel(0x00000074 |
+			       (((k == 1) ? coarse_dqs[dqs] : test_dqs) << 12) |
+			       (((k == 0) ? val : test_dqs) << 8),
+			       (void *)MT76XX_MEMCTRL_BASE + 0x64);
+		else
+			writel(0x00007400 |
+			       (((k == 1) ? coarse_dqs[dqs] : test_dqs) << 4) |
+			       (((k == 0) ? val : test_dqs) << 0),
+			       (void *)MT76XX_MEMCTRL_BASE + 0x64);
+		wmb();		/* Make sure store if finished */
+
+		invalidate_dcache_range((u32)c_addr,
+					(u32)c_addr +
+					NUM_OF_CACHELINE * 32);
+		wmb();		/* Make sure store if finished */
+
+		for (i = 0; i < NUM_OF_CACHELINE * 8; i++) {
+			if (i % 8 == 0)
+				pref_op(0, &c_addr[i]);
+		}
+
+		for (i = 0; i < NUM_OF_CACHELINE * 8; i++) {
+			if (c_addr[i] != nc_addr + i + pat)
+				return -1;
+		}
+	}
+
+	return 0;
+}
+
+void ddr_calibrate(void)
+{
+	u32 min_coarse_dqs[2];
+	u32 max_coarse_dqs[2];
+	u32 min_fine_dqs[2];
+	u32 max_fine_dqs[2];
+	u32 coarse_dqs[2];
+	u32 fine_dqs[2];
+	int reg = 0, ddr_cfg2_reg;
+	int flag;
+	int i, k;
+	int dqs = 0;
+	u32 min_coarse_dqs_bnd, min_fine_dqs_bnd, coarse_dqs_dll, fine_dqs_dll;
+	u32 val;
+	u32 fdiv = 0, frac = 0;
+
+	/* Setup clock to run at full speed */
+	val = readl((void *)MT76XX_DYN_CFG0_REG);
+	fdiv = (u32)((val >> 8) & 0x0F);
+	if (CPU_FRAC_DIV < 1 || CPU_FRAC_DIV > 10)
+		frac = val & 0x0f;
+	else
+		frac = CPU_FRAC_DIV;
+
+	while (frac < fdiv) {
+		val = readl((void *)MT76XX_DYN_CFG0_REG);
+		fdiv = (val >> 8) & 0x0f;
+		fdiv--;
+		val &= ~(0x0f << 8);
+		val |= (fdiv << 8);
+		writel(val, (void *)MT76XX_DYN_CFG0_REG);
+		udelay(500);
+		val = readl((void *)MT76XX_DYN_CFG0_REG);
+		fdiv = (val >> 8) & 0x0f;
+	}
+
+	clrbits_le32((void *)MT76XX_MEMCTRL_BASE + 0x10, BIT(4));
+	ddr_cfg2_reg = readl((void *)MT76XX_MEMCTRL_BASE + 0x48);
+	clrbits_le32((void *)MT76XX_MEMCTRL_BASE + 0x48,
+		     (0x3 << 28) | (0x3 << 26));
+
+	min_coarse_dqs[0] = MIN_START;
+	min_coarse_dqs[1] = MIN_START;
+	min_fine_dqs[0] = MIN_FINE_START;
+	min_fine_dqs[1] = MIN_FINE_START;
+	max_coarse_dqs[0] = MAX_START;
+	max_coarse_dqs[1] = MAX_START;
+	max_fine_dqs[0] = MAX_FINE_START;
+	max_fine_dqs[1] = MAX_FINE_START;
+	dqs = 0;
+
+	/* Add by KP, DQS MIN boundary */
+	reg = readl((void *)MT76XX_MEMCTRL_BASE + 0x20);
+	coarse_dqs_dll = (reg & 0xf00) >> 8;
+	fine_dqs_dll = (reg & 0xf0) >> 4;
+	if (coarse_dqs_dll <= 8)
+		min_coarse_dqs_bnd = 8 - coarse_dqs_dll;
+	else
+		min_coarse_dqs_bnd = 0;
+
+	if (fine_dqs_dll <= 8)
+		min_fine_dqs_bnd = 8 - fine_dqs_dll;
+	else
+		min_fine_dqs_bnd = 0;
+	/* DQS MIN boundary */
+
+DQS_CAL:
+
+	for (k = 0; k < 2; k++) {
+		u32 test_dqs;
+
+		if (k == 0)
+			test_dqs = MAX_START;
+		else
+			test_dqs = MAX_FINE_START;
+
+		do {
+			flag = test_loop(k, dqs, test_dqs, max_coarse_dqs,
+					 0x400, 0x3, 0xf);
+			if (flag == -1)
+				break;
+
+			test_dqs++;
+		} while (test_dqs <= 0xf);
+
+		if (k == 0) {
+			max_coarse_dqs[dqs] = test_dqs;
+		} else {
+			test_dqs--;
+
+			if (test_dqs == MAX_FINE_START - 1) {
+				max_coarse_dqs[dqs]--;
+				max_fine_dqs[dqs] = 0xf;
+			} else {
+				max_fine_dqs[dqs] = test_dqs;
+			}
+		}
+	}
+
+	for (k = 0; k < 2; k++) {
+		u32 test_dqs;
+
+		if (k == 0)
+			test_dqs = MIN_START;
+		else
+			test_dqs = MIN_FINE_START;
+
+		do {
+			flag = test_loop(k, dqs, test_dqs, min_coarse_dqs,
+					 0x480, 0x1, 0x0);
+			if (k == 0) {
+				if (flag == -1 ||
+				    test_dqs == min_coarse_dqs_bnd)
+					break;
+
+				test_dqs--;
+
+				if (test_dqs < min_coarse_dqs_bnd)
+					break;
+			} else {
+				if (flag == -1) {
+					test_dqs++;
+					break;
+				} else if (test_dqs == min_fine_dqs_bnd) {
+					break;
+				}
+
+				test_dqs--;
+
+				if (test_dqs < min_fine_dqs_bnd)
+					break;
+			}
+		} while (test_dqs >= 0);
+
+		if (k == 0) {
+			min_coarse_dqs[dqs] = test_dqs;
+		} else {
+			if (test_dqs == MIN_FINE_START + 1) {
+				min_coarse_dqs[dqs]++;
+				min_fine_dqs[dqs] = 0x0;
+			} else {
+				min_fine_dqs[dqs] = test_dqs;
+			}
+		}
+	}
+
+	if (dqs == 0) {
+		dqs = 1;
+		goto DQS_CAL;
+	}
+
+	for (i = 0; i < 2; i++) {
+		u32 temp;
+
+		coarse_dqs[i] = (max_coarse_dqs[i] + min_coarse_dqs[i]) >> 1;
+		temp =
+		    (((max_coarse_dqs[i] + min_coarse_dqs[i]) % 2) * 4) +
+		    ((max_fine_dqs[i] + min_fine_dqs[i]) >> 1);
+		if (temp >= 0x10) {
+			coarse_dqs[i]++;
+			fine_dqs[i] = (temp - 0x10) + 0x8;
+		} else {
+			fine_dqs[i] = temp;
+		}
+	}
+	reg = (coarse_dqs[1] << 12) | (fine_dqs[1] << 8) |
+		(coarse_dqs[0] << 4) | fine_dqs[0];
+
+	clrbits_le32((void *)MT76XX_MEMCTRL_BASE + 0x10, BIT(4));
+	writel(reg, (void *)MT76XX_MEMCTRL_BASE + 0x64);
+	writel(ddr_cfg2_reg, (void *)MT76XX_MEMCTRL_BASE + 0x48);
+	setbits_le32((void *)MT76XX_MEMCTRL_BASE + 0x10, BIT(4));
+
+	for (i = 0; i < 2; i++)
+		debug("[%02X%02X%02X%02X]", min_coarse_dqs[i],
+		      min_fine_dqs[i], max_coarse_dqs[i], max_fine_dqs[i]);
+	debug("\nDDR Calibration DQS reg = %08X\n", reg);
+}
diff --git a/arch/mips/mach-mt7620/lowlevel_init.S b/arch/mips/mach-mt7620/lowlevel_init.S
new file mode 100644
index 0000000..1a50f160
--- /dev/null
+++ b/arch/mips/mach-mt7620/lowlevel_init.S
@@ -0,0 +1,322 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * (c) 2018 Stefan Roese <sr@denx.de>
+ *
+ * This code is mostly based on the code extracted from this MediaTek
+ * github repository:
+ *
+ * https://github.com/MediaTek-Labs/linkit-smart-uboot.git
+ *
+ * I was not able to find a specific license or other developers
+ * copyrights here, so I can't add them here.
+ */
+
+#include <config.h>
+#include <asm/regdef.h>
+#include <asm/mipsregs.h>
+#include <asm/addrspace.h>
+#include <asm/asm.h>
+#include "mt76xx.h"
+
+#ifndef BIT
+#define BIT(nr)			(1 << (nr))
+#endif
+
+#define DELAY_USEC(us)		((us) / 100)
+
+#define DDR_CFG1_CHIP_WIDTH_MASK (0x3 << 16)
+#define DDR_CFG1_BUS_WIDTH_MASK	(0x3 << 12)
+
+#if defined(CONFIG_ONBOARD_DDR2_SIZE_256MBIT)
+#define DDR_CFG1_SIZE_VAL	0x222e2323
+#define DDR_CFG4_SIZE_VAL	7
+#endif
+#if defined(CONFIG_ONBOARD_DDR2_SIZE_512MBIT)
+#define DDR_CFG1_SIZE_VAL	0x22322323
+#define DDR_CFG4_SIZE_VAL	9
+#endif
+#if defined(CONFIG_ONBOARD_DDR2_SIZE_1024MBIT)
+#define DDR_CFG1_SIZE_VAL	0x22362323
+#define DDR_CFG4_SIZE_VAL	9
+#endif
+#if defined(CONFIG_ONBOARD_DDR2_SIZE_2048MBIT)
+#define DDR_CFG1_SIZE_VAL	0x223a2323
+#define DDR_CFG4_SIZE_VAL	9
+#endif
+
+#if defined(CONFIG_ONBOARD_DDR2_CHIP_WIDTH_8BIT)
+#define DDR_CFG1_CHIP_WIDTH_VAL	(0x1 << 16)
+#endif
+#if defined(CONFIG_ONBOARD_DDR2_CHIP_WIDTH_16BIT)
+#define DDR_CFG1_CHIP_WIDTH_VAL	(0x2 << 16)
+#endif
+
+#if defined(CONFIG_ONBOARD_DDR2_BUS_WIDTH_16BIT)
+#define DDR_CFG1_BUS_WIDTH_VAL	(0x2 << 12)
+#endif
+#if defined(CONFIG_ONBOARD_DDR2_BUS_WIDTH_32BIT)
+#define DDR_CFG1_BUS_WIDTH_VAL	(0x3 << 12)
+#endif
+
+	.set noreorder
+
+LEAF(lowlevel_init)
+
+	/* Load base addresses as physical addresses for later usage */
+	li	s0, CKSEG1ADDR(MT76XX_SYSCTL_BASE)
+	li	s1, CKSEG1ADDR(MT76XX_MEMCTRL_BASE)
+	li	s2, CKSEG1ADDR(MT76XX_RGCTRL_BASE)
+
+	/* polling CPLL is ready */
+	li	t1, DELAY_USEC(1000000)
+	la	t5, MT76XX_ROM_STATUS_REG
+1:
+	lw	t2, 0(t5)
+	andi	t2, t2, 0x1
+	bnez	t2, CPLL_READY
+	subu	t1, t1, 1
+	bgtz	t1, 1b
+	nop
+	la      t0, MT76XX_CLKCFG0_REG
+	lw      t3, 0(t0)
+	ori	t3, t3, 0x1
+	sw	t3, 0(t0)
+	b	CPLL_DONE
+	nop
+CPLL_READY:
+	la	t0, MT76XX_CLKCFG0_REG
+	lw	t1, 0(t0)
+	li	t2, ~0x0c
+	and	t1, t1, t2
+	ori	t1, t1, 0xc
+	sw	t1, 0(t0)
+	la	t0, MT76XX_DYN_CFG0_REG
+	lw	t3, 0(t0)
+	li	t5, ~((0x0f << 8) | (0x0f << 0))
+	and	t3, t3, t5
+	li	t5, (10 << 8) | (1 << 0)
+	or	t3, t3, t5
+	sw	t3, 0(t0)
+	la	t0, MT76XX_CLKCFG0_REG
+	lw	t3, 0(t0)
+	li	t4, ~0x0F
+	and     t3, t3, t4
+	ori	t3, t3, 0xc
+	sw	t3, 0(t0)
+	lw	t3, 0(t0)
+	ori	t3, t3, 0x08
+	sw	t3, 0(t0)
+
+CPLL_DONE:
+	/*
+	 * SDR and DDR initialization: delay 200us
+	 */
+	li	t0, DELAY_USEC(200 + 40)
+	li	t1, 0x1
+1:
+	sub	t0, t0, t1
+	bnez	t0, 1b
+	nop
+
+	/* set DRAM IO PAD for MT7628IC */
+	/* DDR LDO Enable  */
+	lw	t4, 0x100(s2)
+	li	t2, BIT(31)
+	or	t4, t4, t2
+	sw	t4, 0x100(s2)
+	lw	t4, 0x10c(s2)
+	j	LDO_1P8V
+	nop
+LDO_1P8V:
+	li	t2, ~BIT(6)
+	and	t4, t4, t2
+	sw	t4, 0x10c(s2)
+	j	DDRLDO_SOFT_START
+LDO_2P5V:
+	/* suppose external DDR1 LDO 2.5V */
+	li	t2, BIT(6)
+	or	t4, t4, t2
+	sw	t4, 0x10c(s2)
+
+DDRLDO_SOFT_START:
+	lw	t2, 0x10c(s2)
+	li	t3, BIT(16)
+	or	t2, t2, t3
+	sw	t2, 0x10c(s2)
+	li	t3, DELAY_USEC(250*50)
+LDO_DELAY:
+	subu	t3, t3, 1
+	bnez	t3, LDO_DELAY
+	nop
+
+	lw	t2, 0x10c(s2)
+	li	t3, BIT(18)
+	or	t2, t2, t3
+	sw	t2, 0x10c(s2)
+
+SET_RG_BUCK_FPWM:
+	lw	t2, 0x104(s2)
+	ori	t2, t2, BIT(10)
+	sw	t2, 0x104(s2)
+
+DDR_PAD_CFG:
+	/* clean CLK PAD */
+	lw	t2, 0x704(s2)
+	li	t8, 0xfffff0f0
+	and	t2, t2, t8
+	/* clean CMD PAD */
+	lw	t3, 0x70c(s2)
+	li	t8, 0xfffff0f0
+	and	t3, t3, t8
+	/* clean DQ IPAD */
+	lw	t4, 0x710(s2)
+	li	t8, 0xfffff8ff
+	and	t4, t4, t8
+	/* clean DQ OPAD */
+	lw	t5, 0x714(s2)
+	li	t8, 0xfffff0f0
+	and	t5, t5, t8
+	/* clean DQS IPAD */
+	lw	t6, 0x718(s2)
+	li	t8, 0xfffff8ff
+	and	t6, t6, t8
+	/* clean DQS OPAD */
+	lw	t7, 0x71c(s2)
+	li	t8, 0xfffff0f0
+	and	t7, t7, t8
+
+	lw	t9, 0xc(s0)
+	srl	t9, t9, 16
+	andi	t9, t9, 0x1
+	bnez	t9, MT7628_AN_DDR1_PAD
+MT7628_KN_PAD:
+	li	t8, 0x00000303
+	or	t2, t2, t8
+	or	t3, t3, t8
+	or	t5, t5, t8
+	or	t7, t7, t8
+	li	t8, 0x00000000
+	or	t4, t4, t8
+	or	t6, t6, t8
+	j	SET_PAD_CFG
+MT7628_AN_DDR1_PAD:
+	lw	t1, 0x10(s0)
+	andi	t1, t1, 0x1
+	beqz	t1, MT7628_AN_DDR2_PAD
+	li	t8, 0x00000c0c
+	or	t2, t2, t8
+	li	t8, 0x00000202
+	or	t3, t3, t8
+	li	t8, 0x00000707
+	or	t5, t5, t8
+	li	t8, 0x00000c0c
+	or	t7, t7, t8
+	li	t8, 0x00000000
+	or	t4, t4, t8
+	or	t6, t6, t8
+	j	SET_PAD_CFG
+MT7628_AN_DDR2_PAD:
+	li	t8, 0x00000c0c
+	or	t2, t2, t8
+	li	t8, 0x00000202
+	or	t3, t3, t8
+	li	t8, 0x00000404
+	or	t5, t5, t8
+	li	t8, 0x00000c0c
+	or	t7, t7, t8
+	li	t8, 0x00000000		/* ODT off */
+	or	t4, t4, t8
+	or	t6, t6, t8
+
+SET_PAD_CFG:
+	sw	t2, 0x704(s2)
+	sw	t3, 0x70c(s2)
+	sw	t4, 0x710(s2)
+	sw	t5, 0x714(s2)
+	sw	t6, 0x718(s2)
+	sw	t7, 0x71c(s2)
+
+	/*
+	 * DDR initialization: reset pin to 0
+	 */
+	lw	t2, 0x34(s0)
+	and	t2, ~BIT(10)
+	sw	t2, 0x34(s0)
+	nop
+
+	/*
+	 * DDR initialization: wait til reg DDR_CFG1 bit 21 equal to 1 (ready)
+	 */
+DDR_READY:
+	li	t1, DDR_CFG1_REG
+	lw	t0, 0(t1)
+	nop
+	and	t2, t0, BIT(21)
+	beqz	t2, DDR_READY
+	nop
+
+	/*
+	 * DDR initialization
+	 *
+	 * Only DDR2 supported right now. DDR2 support can be added, once
+	 * boards using it will get added to mainline U-Boot.
+	 */
+	li	t1, DDR_CFG2_REG
+	lw	t0, 0(t1)
+	nop
+	and	t0, ~BIT(30)
+	and	t0, ~(7 << 4)
+	or	t0, (4 << 4)
+	or	t0, BIT(30)
+	or	t0, BIT(11)
+	sw	t0, 0(t1)
+	nop
+
+	li	t1, DDR_CFG3_REG
+	lw	t2, 0(t1)
+	/* Disable ODT; reference board ok, ev board fail */
+	and	t2, ~BIT(6)
+	or	t2, BIT(2)
+	li	t0, DDR_CFG4_REG
+	lw	t1, 0(t0)
+	li	t2, ~(0x01f | 0x0f0)
+	and	t1, t1, t2
+	ori	t1, t1, DDR_CFG4_SIZE_VAL
+	sw	t1, 0(t0)
+	nop
+
+	/*
+	 * DDR initialization: config size and width on reg DDR_CFG1
+	 */
+	li	t6, DDR_CFG1_SIZE_VAL
+
+	and	t6, ~DDR_CFG1_CHIP_WIDTH_MASK
+	or	t6, DDR_CFG1_CHIP_WIDTH_VAL
+
+	/* CONFIG DDR_CFG1[13:12] about TOTAL WIDTH */
+	and	t6, ~DDR_CFG1_BUS_WIDTH_MASK
+	or	t6, DDR_CFG1_BUS_WIDTH_VAL
+
+	li	t5, DDR_CFG1_REG
+	sw	t6, 0(t5)
+	nop
+
+	/*
+	 * DDR: enable self auto refresh for power saving
+	 * enable it by default for both RAM and ROM version (for CoC)
+	 */
+	lw	t1, 0x14(s1)
+	nop
+	and	t1, 0xff000000
+	or	t1, 0x01
+	sw	t1, 0x14(s1)
+	nop
+	lw	t1, 0x10(s1)
+	nop
+	or	t1, 0x10
+	sw	t1, 0x10(s1)
+	nop
+
+	jr	ra
+	nop
+	END(lowlevel_init)
diff --git a/arch/mips/mach-mt7620/mt76xx.h b/arch/mips/mach-mt7620/mt76xx.h
new file mode 100644
index 0000000..17473ea
--- /dev/null
+++ b/arch/mips/mach-mt7620/mt76xx.h
@@ -0,0 +1,32 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2018 Stefan Roese <sr@denx.de>
+ */
+
+#ifndef __MT76XX_H
+#define __MT76XX_H
+
+#define MT76XX_SYSCTL_BASE	0x10000000
+
+#define MT76XX_CHIPID_OFFS	0x00
+#define MT76XX_CHIP_REV_ID_OFFS	0x0c
+#define MT76XX_SYSCFG0_OFFS	0x10
+
+#define MT76XX_MEMCTRL_BASE	(MT76XX_SYSCTL_BASE + 0x0300)
+#define MT76XX_RGCTRL_BASE	(MT76XX_SYSCTL_BASE + 0x1000)
+
+#define MT76XX_ROM_STATUS_REG	(MT76XX_SYSCTL_BASE + 0x0028)
+#define MT76XX_CLKCFG0_REG	(MT76XX_SYSCTL_BASE + 0x002c)
+#define MT76XX_DYN_CFG0_REG	(MT76XX_SYSCTL_BASE + 0x0440)
+
+#define DDR_CFG1_REG		(MT76XX_MEMCTRL_BASE + 0x44)
+#define DDR_CFG2_REG		(MT76XX_MEMCTRL_BASE + 0x48)
+#define DDR_CFG3_REG		(MT76XX_MEMCTRL_BASE + 0x4c)
+#define DDR_CFG4_REG		(MT76XX_MEMCTRL_BASE + 0x50)
+
+#ifndef __ASSEMBLY__
+/* Prototypes */
+void ddr_calibrate(void);
+#endif
+
+#endif